High potential is normally abbreviated as hipot. It is a term used in reference to a specific form of electrical safety testing apparatus, called a hipot tester. These apparatuses are used to verify electrical insulation of finished appliances, cables and other devices composed of wires. Transformers, printed circuit boards, and electric motors are among such devices.
After a product/appliance has been manufactured or assembled, it is usually normal that there will be some level of current leakage. The amount of current leakage experienced is usually minimal and is caused by voltages and internal capacitance within the product. This leakage is normal and should be expected in every device. However, there are certain cases where excessive leakage current flow can occur due to various reasons.
Faults in the design or disintegration of product insulation among many other reasons may be the cause of the excessive leakage. These flaws often cause excessive leaking of current and may give rise to electrical shock for any individual that comes into contact with the defective appliance. The essence of a hipot test is to ensure and verify that the product has enough insulation so that the user of the device may not be electrocuted.
Dielectric Withstanding Voltage (DWV) is another term used in place of the term hipot test. This process involves application of a high voltage between the earth ground shielding and the conductor in the product that carry current. Exposure to excessive voltage causes resultant current flow through the product. A high potential tester is the gadget used in monitoring of this resultant current, which is also called leakage current.
This process of testing has its basis on a major assumption. The assumption is that if the device works safely without its insulation breaking after being exposed to high voltage, then it can work fine under normal working conditions. During normal operation, the device should be able to withstand standard voltage application. This assumption is the source of the term Dielectric Withstanding Voltage.
The aim of the test is to stress the insulation used in the product. However, besides stressing the insulation, the test is also used to detect defects in workmanship. The most important aspects of workmanship that are monitored are the small gap spacings that occur between current-carrying conductors and earth ground. Under normal operating environment, these small gaps can be closed by contaminants, shock, vibration, humidity, and dirt.
When these small gaps close, the flow of current is enabled. This flow of current can be a major electrical hazard. Prior to product release into the market, it must be tested verify that such hazards cannot occur. The only applicable method that can be used in the detection of this type of defects is DWV. This is true in spite of there being other viable methods.
Manufacturers use high potential testers to do the verification of electrical insulation. Often, this simple electric device comprises of a switching matrix, current meter, and a source for the high voltage. All the points located on the cable are connected to the high-voltage source and the current meter through the matrix. Including a display and a microcontroller helps to automate the testing process.
After a product/appliance has been manufactured or assembled, it is usually normal that there will be some level of current leakage. The amount of current leakage experienced is usually minimal and is caused by voltages and internal capacitance within the product. This leakage is normal and should be expected in every device. However, there are certain cases where excessive leakage current flow can occur due to various reasons.
Faults in the design or disintegration of product insulation among many other reasons may be the cause of the excessive leakage. These flaws often cause excessive leaking of current and may give rise to electrical shock for any individual that comes into contact with the defective appliance. The essence of a hipot test is to ensure and verify that the product has enough insulation so that the user of the device may not be electrocuted.
Dielectric Withstanding Voltage (DWV) is another term used in place of the term hipot test. This process involves application of a high voltage between the earth ground shielding and the conductor in the product that carry current. Exposure to excessive voltage causes resultant current flow through the product. A high potential tester is the gadget used in monitoring of this resultant current, which is also called leakage current.
This process of testing has its basis on a major assumption. The assumption is that if the device works safely without its insulation breaking after being exposed to high voltage, then it can work fine under normal working conditions. During normal operation, the device should be able to withstand standard voltage application. This assumption is the source of the term Dielectric Withstanding Voltage.
The aim of the test is to stress the insulation used in the product. However, besides stressing the insulation, the test is also used to detect defects in workmanship. The most important aspects of workmanship that are monitored are the small gap spacings that occur between current-carrying conductors and earth ground. Under normal operating environment, these small gaps can be closed by contaminants, shock, vibration, humidity, and dirt.
When these small gaps close, the flow of current is enabled. This flow of current can be a major electrical hazard. Prior to product release into the market, it must be tested verify that such hazards cannot occur. The only applicable method that can be used in the detection of this type of defects is DWV. This is true in spite of there being other viable methods.
Manufacturers use high potential testers to do the verification of electrical insulation. Often, this simple electric device comprises of a switching matrix, current meter, and a source for the high voltage. All the points located on the cable are connected to the high-voltage source and the current meter through the matrix. Including a display and a microcontroller helps to automate the testing process.
About the Author:
We have all the detailed specifications on hipot tester the best on our related homepage. Simply use this link to reach the main website at http://www.rossengineeringcorp.com/products/measurement/ac-dc-digital-hipots.html.
0 comments:
Post a Comment